Paradigm > Price Book > USA > 01.2022

ELECTRICITY IMPORTANT: The electrical components for a 3-circuit, 5-wire system differ from those for a 4-circuit, 8-wire system. These components are not interchangeable from one system to the other. Accordingly, special attention is required during specification. Take note of whether the product code includes the digit ‘3’ or ‘4’. W x D x H (in) W x D x H (mm) Code Price ($) W x D x H (in) W x D x H (mm) Code Price ($) ELECTRICAL COMPONENTS – 3-CIRCUIT SYSTEM Hardwire base feed Enables connection of electric system to the floor or wall. Connects to electric system at the location of the receptacle. Note: The housing exceeds the raceway by 1 1 / 2 " (38 mm). Check the clearance required before installing storage units. 72 1829 KEB3-S-6 270 Plug-in base feed, 20-amp Enables connection of electric system to a 20-amp outlet. Connects to electric system at the location of the receptacle. Powers circuit No. 1 only. UL Recognized, cUL Approved. Note: The housing exceeds the raceway by 1 1 / 2 " (38 mm). Check the clearance required before installing storage units. 24 610 KEB3-P-2 277 Concealed base feed Enables connection of electric system to the floor or wall. Meets the standards of the New York City Building Code. Inserts into a non-powered panel and connects in-line to the adjacent panel’s electric panel. Mounting brackets included. Note: Requires piercing of raceway cover. A cover with a Type P cut-out may also be ordered separately. 72 1829 KEB3-C-6 386 Powered feed poles KET3-12 KET3-9 Enables connection of electric system and the running of communication cables to a ceiling with a maximum height of 12' (3657 mm). Connects to the end of an electric system. Includes pole, top caps, ceiling cover plate, power feed and a Y connector. To be installed at end of panel run. 144 3657 KET3-12-___ 1,252 To be installed on an L, T or X junction kit. 114 2895 KET3-9-___ 1,114 Specify trim color. Duplex receptacles, 15-amp Common ground. Pack of 10. 3 1 / 2 x 1 3 / 8 x 1 1 / 2 88 x 35 x 45 KER3-C_-_ 335 Specify type of circuit (1, 2, 3). Specify Black (K) or White (W) color. Power connectors for junctions Required only to power panels separated by a junction kit; refer to page 10. Note: Used as a complement to the electric connector supplied with each powered panel. For L or Type S connection (includes a Y connector). KEJ3-LS 66 For T connection (includes a Y connector and a junction connector). KEJ3-T 131 For X connection (includes two Y connectors and two junction connectors). KEJ3-X 160 For Type G connection (includes a junction connector). KEJ3-G 102 Pass-thru jumper cables for non- powered panel Required only to connect two panels separated by one or several non-powered panel(s). Connector length is adjustable in order to enable a connection through a junction kit. Note: Connector length is 18” (457 mm) greater than the total width of the panel(s) to be crossed. 24" (610 mm) W panel KEJL3-24 139 30" (762 mm) W panel KEJL3-30 146 36" (914 mm) W panel KEJL3-36 153 42" (1067 mm) W panel KEJL3-42 160 48" (1219 mm) W panel(s) KEJL3-48 168 60" (1524 mm) W panel(s) KEJL3-60 183 66" (1676 mm) W panels KEJL3-66 206 72" (1829 mm) W panels KEJL3-72 225 78" (1981 mm) W panels KEJL3-78 244 84" (2134 mm) W panels KEJL3-84 263 90" (2283 mm) W panels KEJL3-90 282 96" (2438 mm) W panels KEJL3-96 301 102" (2591 mm) W panels KEJL3-102 320 108" (2743 mm) W panels KEJL3-108 339 120" (3048 mm) W panels KEJL3-120 358 Electrical retrofit kits Enables retrofit connection of a non-powered panel. Electric system, in-line junction connector and mounting brackets included. 24" (610 mm) W panel KEP3-24 189 30" (762 mm) W panel KEP3-30 233 36" (914 mm) W panel KEP3-36 248 42" (1067 mm) W panel KEP3-42 262 48" (1219 mm) W panel KEP3-48 270 60" (1524 mm) W panel KEP3-60 357 ELECTRICAL COMPONENTS – 4-CIRCUIT SYSTEM Hardwire base feed Enables connection of electric system to the floor or wall. Connects to electric system at the location of the receptacle. Note: The housing exceeds the raceway by 1 1 / 2 " (38 mm). Check the clearance required before installing storage units. 72 1829 KEB4-S-6 335 Plug-in base feed, 20-amp Enables connection of electric system to a 20-amp outlet. Connects to electric system at the location of the receptacle. Powers circuit No. 1 only. UL Recognized, cUL Approved. Note: The housing exceeds the raceway by 1 1 / 2 " (38 mm). Check the clearance required before installing storage units. 24 610 KEB4-P-2 277 Concealed base feed Enables connection of electric system to the floor or wall. Meets the standards of the New York City Building Code. Inserts into a non-powered panel and connects in-line to the adjacent panel’s electric panel. Mounting brackets included. Note: Requires piercing of raceway cover. A cover with a Type P cut-out may also be ordered separately. 72 1829 KEB4-C-6 379 Powered feed poles KET4-12 KET4-9 Enables connection of electric system and the running of communication cables to a ceiling with a maximum height of 12" (3657 mm). Connects to the end of an electric system. Includes pole, top caps, ceiling cover plate and power feed. To be installed at end of panel run. 144 3657 KET4-12-___ 1,354 To be installed on an L, T or X junction kit. 114 2895 KET4-9-___ 1,216 Specify trim color. 29 PARADIGM Panel System USA – JANUARY 2022 PARADIGM Panel System