Paradigm > Price Book > USA > 02.2024

ELECTRICITY IMPORTANT: The electrical components for a 3-circuit, 5-wire system differ from those for a 4-circuit, 8-wire system. These components are not interchangeable from one system to the other. Accordingly, special attention is required during specification. Take note of whether the product code includes the digit ‘3’ or ‘4’. W x D x H (in) W x D x H (mm) Code Price ($) W x D x H (in) W x D x H (mm) Code Price ($) ELECTRICAL COMPONENTS – 3-CIRCUIT SYSTEM Hardwire base feed Enables connection of electric system to the floor or wall. Connects to electric system at the location of the receptacle. Note: The housing exceeds the raceway by 1 1 / 2 " (38 mm). Check the clearance required before installing storage units. 72 1829 KEB3-S-6 281 Plug-in base feed, 20-amp Enables connection of electric system to a 20-amp outlet. Connects to electric system at the location of the receptacle. Powers circuit No. 1 only. UL Recognized, cUL Approved. Note: The housing exceeds the raceway by 1 1 / 2 " (38 mm). Check the clearance required before installing storage units. 24 610 KEB3-P-2 288 Concealed base feed Enables connection of electric system to the floor or wall. Meets the standards of the New York City Building Code. Inserts into a non-powered panel and connects in-line to the adjacent panel’s electric panel. Mounting brackets included. Note: Requires piercing of raceway cover. A cover with a Type P cut-out may also be ordered separately. 72 1829 KEB3-C-6 401 Powered feed poles KET3-12 KET3-9 Enables connection of electric system and the running of communication cables to a ceiling with a maximum height of 12' (3657 mm). Connects to the end of an electric system. Includes pole, top caps, ceiling cover plate, power feed and a Y connector. To be installed at end of panel run. 144 3657 KET3-12-___ 1,302 To be installed on an L, T or X junction kit. 114 2895 KET3-9-___ 1,159 Specify trim color. Duplex receptacles, 15-amp Common ground. Pack of 10. 3 1 / 2 x 1 3 / 8 x 1 1 / 2 88 x 35 x 45 KER3-C_-_ 348 Specify type of circuit (1, 2, 3). Specify Black (K) or White (W) color. Power connectors for junctions Required only to power panels separated by a junction kit; refer to page 10. Note: Used as a complement to the electric connector supplied with each powered panel. For L or Type S connection (includes a Y connector). KEJ3-LS 69 For T connection (includes a Y connector and a junction connector). KEJ3-T 136 For X connection (includes two Y connectors and two junction connectors). KEJ3-X 166 For Type G connection (includes a junction connector). KEJ3-G 106 Pass-thru jumper cables for non- powered panel Required only to connect two panels separated by one or several non-powered panel(s). Connector length is adjustable in order to enable a connection through a junction kit. Note: Connector length is 18” (457 mm) greater than the total width of the panel(s) to be crossed. 24" (610 mm) W panel KEJL3-24 145 30" (762 mm) W panel KEJL3-30 152 36" (914 mm) W panel KEJL3-36 159 42" (1067 mm) W panel KEJL3-42 166 48" (1219 mm) W panel(s) KEJL3-48 175 60" (1524 mm) W panel(s) KEJL3-60 190 66" (1676 mm) W panels KEJL3-66 214 72" (1829 mm) W panels KEJL3-72 234 78" (1981 mm) W panels KEJL3-78 254 84" (2134 mm) W panels KEJL3-84 274 90" (2283 mm) W panels KEJL3-90 293 96" (2438 mm) W panels KEJL3-96 313 102" (2591 mm) W panels KEJL3-102 333 108" (2743 mm) W panels KEJL3-108 353 120" (3048 mm) W panels KEJL3-120 372 Electrical retrofit kits Enables retrofit connection of a non-powered panel. Electric system, in-line junction connector and mounting brackets included. 24" (610 mm) W panel KEP3-24 197 30" (762 mm) W panel KEP3-30 242 36" (914 mm) W panel KEP3-36 258 42" (1067 mm) W panel KEP3-42 272 48" (1219 mm) W panel KEP3-48 281 60" (1524 mm) W panel KEP3-60 371 ELECTRICAL COMPONENTS – 4-CIRCUIT SYSTEM Hardwire base feed Enables connection of electric system to the floor or wall. Connects to electric system at the location of the receptacle. Note: The housing exceeds the raceway by 1 1 / 2 " (38 mm). Check the clearance required before installing storage units. 72 1829 KEB4-S-6 348 Plug-in base feed, 20-amp Enables connection of electric system to a 20-amp outlet. Connects to electric system at the location of the receptacle. Powers circuit No. 1 only. UL Recognized, cUL Approved. Note: The housing exceeds the raceway by 1 1 / 2 " (38 mm). Check the clearance required before installing storage units. 24 610 KEB4-P-2 288 Concealed base feed Enables connection of electric system to the floor or wall. Meets the standards of the New York City Building Code. Inserts into a non-powered panel and connects in-line to the adjacent panel’s electric panel. Mounting brackets included. Note: Requires piercing of raceway cover. A cover with a Type P cut-out may also be ordered separately. 72 1829 KEB4-C-6 394 Powered feed poles KET4-12 KET4-9 Enables connection of electric system and the running of communication cables to a ceiling with a maximum height of 12" (3657 mm). Connects to the end of an electric system. Includes pole, top caps, ceiling cover plate and power feed. To be installed at end of panel run. 144 3657 KET4-12-___ 1,408 To be installed on an L, T or X junction kit. 114 2895 KET4-9-___ 1,265 Specify trim color. 29 PARADIGM Panel System USA – FEBRUARY 2024 PARADIGM Panel System